The store will not work correctly in the case when cookies are disabled.
JavaScript lijkt te zijn uitgeschakeld in uw browser.
Voor de beste gebruikerservaring, zorg ervoor dat javascript ingeschakeld is voor uw browser.
Used | DBX - 2231
Revolutionary instant encode/decode Type III® Noise Reduction in-circuit at the push of the button. Increases S/N ratio by up to 20dB
Patent-pending PeakPlus™ Limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
Four segment LED bargraph for BOTH Gain Reduction AND Output Level
Status LEDs offer visual feedback for all settings on the front panel
Input connectors: 1/4'' TRS, female XLR (pin 2 hot), and barrier terminal strip
Input type: Electronically balanced/unbalanced,RF filtered
Input impedance: Balanced 40kOhm, unbalanced 20kOhm
Max input: >21 dBy balanced or unbalanced
CMRR: >40dB, typically >55dB at 1 kHz
Output connectors: 1/4'' TRS, male XLR (pin 2 hot), and barrier terminal strip
Output type: Impedance-balanced/unbalanced, RF filtered
Output impedance: Balanced 200 ohm, unbalanced 100 ohm
Max output:
>+21dBu balanced/unbalanced into 2 kOhm or greater;
>+18dBm balanced/unbalanced (into 600 ohm)
Bandwidth: 20Hz to 20 kHz, +/-0,5dB
Frequency response: <10Hz to > 50kHz, +0,5/-3dB
Signal-to-Noise (NR In: +/-6 and +/-15dB ranges): >102dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
Dynamic Range (NR In: +/-6dB and +/-15dB ranges): >120dB, unweighted
Signal-to-Noise (NR Out: +/-6dB range): >94dB, unweighted, ref: +4dBu, 22kHz measurment bandwidth
Dynamic Range (NR Out: +/-6dB range): >112dB, unweighted
Signal-to-Noise (NR Out: +/-15dB range): >90dB, unweighted, ref: +4dBu, 22kHz measurement bandwidth
Dynamic Range (NR Out: +/-15dB range): >108dB, unweighted
THD+Noise: <0.04%, 0.02% typical at +4dBu, 1kHz
Interchannel Crosstalk: <-80dB, 20Hz to 20kHz
Noise Reduction: Up to 20dB of dynamic broadband noise reduction
NR Switch: Activates dbx Type III Noise Reduction
Bypass Switch: Bypasses the graphic equalizer section in the signal path
Low cut Switch: (recessed) Activates the 40Hz 18dB/octave Bessel high-pass filter
Range Switch: (recessed) Selects either +/- 6dB or +/- 15dB slider boost/cut range
I/O Meter: 4-LED bar graph (Green, Green, Yellow, Red) at -10, 0, +10, and +18dBu
Gain Reduction Meter: 4-LED bar graph (all Red) at 0, 3, 6, and 10dB
Indicators: NR Active (Yellow); EQ Bypass (Red); Clip (Red); Low Cut (Red); +/-6dB (Yellow); +/-15dB (Red)
Operating Voltage: 100VAC 50/60Hz; 120VAC 60Hz; 230VAC 50/60Hz
Power consumption: 28W
Power connector: IEC receptacle
Dimensions: 5.25" H X 19" W X 7.9" D (13.335cm x 48.3cm x 20.1cm)
Meer informatie
Conditie
Gebruikt